NOVEMBER 2020 Update Release

All New Systems Support, Support UP TO 2020:
Model XC90, year 2016~2020:

• • • ECM – Engine Control Module
    • SUM – Suspension Module
    • BECM – Battery Energy Control Module
    • EGSM – Electronic Gear Selector Module
    • IEM – Inverter Electric rear axle drive Module
    • IGM – Inverter Generator Module
    • OBC – On-Board Charger Module
    • TEM – Telematics Module
    • TACM – Transmission Actuator Control Module

All systems includes reading DTCs, clearing DTCs, and Data Stream functions.

Newly Supported Adaptation Functions
Model XC60, year 2016~2017, ECM – Diesel Engine Control module system, new supported Adaptation functions:

• • • Combustion of soot in DPF
    • Resetting adaptation for fuel flow regulation valve
    • Resetting adaptations for swirl damper
    • Resetting adaptations for turbocharger control
    • Resetting adaptations for the EGR valve
    • Resetting adaptations for the diesel particle filter
    • Resetting adaptations for the particle filter’s differential pressure sensor
    • Resetting adaptations for front heated oxygen sensor
    • Resetting adaptations for rear heated oxygen sensor
    • Resetting adaptations for the injectors
    • Entering the engine oil level after service
    • Resetting the counter for the particle filter
    • Adaptation of throttle module
    • Adaptation of the exhaust gas recirculation (EGR) valve
    • Adjusting calculated oil level / oil quality
    • Adaptation of differential pressure sensor particle filter

Model XC60, year 2016~2018, ECM – Petrol Engine Control Module, new supported Adaptation functions:

• • • Resetting adaptations and wear counter for supercharger
    • Resetting adaptations for fuel / air mix (fuel trim)
    • Resetting adaptations for rear heated oxygen sensor regulation
    • Resetting adaptations for camshaft regulation, intake
    • Resetting adaptations for camshaft regulation, exhaust
    • Resetting adaptations for the fuel pump, low pressure side
    • Resetting adaptations for cylinder balancing
    • Resetting adaptations for the throttle
    • Entering the engine oil level after service
    • Resetting adaptation for the compressor bypass valve
    • Resetting the fuel adaption values
    • Resetting the flywheel adaptions
    • Resetting the camshaft adaption values
    • Resetting of adaptations value for the lambda probe, rear
    • Resetting of adaptations value for the lambda probe, front
    • Resetting adaptations for the throttle unit
    • Resetting adaptations for the gasoline particulate filter
    • Resetting of adaptation values for the pressure sensor, particulate filter

Model XC60, year 2016~2018, TCM (Transmission Control Module – AWD), new supported Adaptation functions:

• • • Resetting adaptation
    • Calibration of gear position sensor
    • Resetting the ‘Transmission fluid change’ counter

Model XC60, year 2013~2018, DDM – Driver Door Module, new supported Adaptation functions:

• • • Initiate the window in the front door
    • Initiate the window in the rear door

Model XC60, year 2013~2018, PDM – Passenger Door Module, new supported Adaptation functions:

• • • Initiate the window in the front door
    • Initiate the window in the rear door

Model XC60, year 2012~2017, POT – Power Operating Tailgate Module , new supported Adaptation functions:

• • • Activation of boot lid opening/closing
    • Resetting the learned maximum opening angle

New Supported Activation Functions
Model C30, year 2009~2010, ECM – Engine Control Module, new supported Activation function
Model S40, year 2009~2010, ECM – Engine Control Module, new supported Activation function
Model V40, year 2015, ECM – Engine Control Module, new supported Activation function

New Supported Data Stream Capabilities

Model XC60, year 2016~2018, ECM – Engine Control Module, new Data Stream capabilities

Model XC60, year 2018:

• • • TCM
    • DEM – Differential Electronic Module
    • BCM – Brake Control Module
    • SAS – Steering Wheel Angle Sensor Module
    • PSCM – Power Steering Control module
    • VDDM – Vehicle Dynamic Domain Master
    • SUM – Suspension Module
    • SRS
    • DDM – Driver Door Module
    • PDM – Passenger Door Module
    • POT – Power Operating Tailgate Module
    • PSMP – Power Seat Module Passenger
    • PSMD – Power Seat Module Driver
    • BMS – Battery Monitoring Sensor
    • GSM – Gear Selector Module
    • OHC – Overhead Console
    • CSD – Center Stack Display
    • CCM – Climate Control Module
    • DIM – Instrument Cluster Module
    • CEM – Central Electronic Module
    • AUD – Audio ModuleIHU – Infotainment Head Unit
    • PAM – Parking Assist Module
    • SODL – Side Obstacle Detection Control Module Left
    • SODR – Side Obstacle Detection Control Module Right
    • ASDM – Active Safety Domain Master
    • RML – Restraint Module Left
    • RMR – Restraint Module RightVCM – Vehicle Connectivity Module
    • WAM – Wide Angle Vision Module
    • SWM – Steering Wheel Module

Newly Supported Whole System Search Function, Generate Diagnostic Report Function Added

• Model S80, year 1999~2016
• Model XC60, year 2009~2017
• Model XC90, year 2003~2020

Newly Improved Whole System Search Function

• Model XC90, year 2016~2020

June 2020 Update Release

NEW SUPPORTED ADAPTATION SPECIAL FUNCTIONS

Model V40, Year 2018, CEM/ Central Electronic Module, New Supported Adaptation Function:

1. • Battery Reset To Zero Service
2. • Resetting the Information to Zero on Power Supply When Replacing the Battery Monitoring Sensor (BMS)

Model V40, Year 2016-2018, ECM/ Petrol Engine Control Module, New Supported Adaptation Function:

1. ◦ Resetting Adaptations and Wear Counter for Supercharge
2. ◦ Resetting Adaptations for Fuel / Air Mix (Fuel Trim)
3. ◦ Resetting Adaptations for Rear Heated Oxygen Sensor Regulation
4. ◦ Resetting Adaptations for Camshaft Regulation, Intake
5. ◦ Resetting Adaptations for Camshaft Regulation, Exhaust
6. ◦ Resetting Adaptations for the Fuel Pump, Low Pressure Side
7. ◦ Resetting Adaptations for Cylinder Balancing
8. ◦ Resetting Adaptations for the Throttle
9. ◦ Entering the Engine Oil Level After Service

Model V40, Year 2016-2018, TCM System, New Supported Adaptation Functions:

1. ◦ Resetting Adaptation
2. ◦ Calibration of Gear Position Sensor

Model V40, Year 2016~2018, DDM (Driver Door Module) & PDM (Passenger Door Module), New Supported Adaptation Functions:

1. • Initiate the Window in the Front Door
2. • Initiate the Window in the Rear Door

Model V40, Year 2017, ECM / Diesel Engine Control Module, New Supported Adaptation Functions:

1. • Combustion of Soot in the Particle Filter

   • Resetting Adaptations for Fuel Flow Regulation Valve

   • Resetting Adaptations for Swirl Damper

   • Resetting Adaptations for Turbocharger Control

   • Resetting Adaptations for the EGR Valve

   • Resetting Adaptations for the Diesel Particle Filter

   • Resetting Adaptations for the Particle Filters Differential Pressure Sensor

   • Resetting Adaptations for Front Heated Oxygen Sensor

   • Resetting Adaptations for Rear Heated Oxygen Sensor

   • Resetting Adaptations for the Injectors, Entering the Engine Oil Level After Service

Model XC90, Year 2016~2020, ECM / Petrol Engine Control Module, New Supported Adaptation Functions:

• Resetting Adaptations for Fuel / Air Mix (Fuel Trim)

• Resetting of Adaptations Values for the Lambda Probe2

• Resetting of Adaptations Value for Probe, Front

• Resetting Adaptations for the Fuel pump, Low Pressure Side

• Resetting Adaptations for the Throttle Unit

• Resetting Adaptations for the Gasoline Particulate Filter

• Resetting of Adaptation Values for the Pressure Sensor, Particulate Filter

• Resetting Adaptations and wear Counter for Supercharger

Model XC90, Year 2016~2020, ECM / Diesel Engine Control Module, New Supported Adaptation Functions:

• Resetting of Adaptation Values for the Control valve, Fuel Flow

• Resetting of Adaptation Values for the Swirl Actuator

• Resetting of Adaptation Values for the Variable Nozzle Turbine Turbo

• Resetting Adaptations for the EGR Valve

• Resetting Adaptations for the Diesel Particle Filter

• Resetting of Adaptation Values for the Pressure Sensor, Particulate Filter

• Resetting of Adaptations Value for the Lambda Probe, Front

• Resetting of Adaptations Values for the Lambda Probe2

• Resetting of Adaptations Adaptation for the Injectors

Model XC90, Year 2016~2020, TCM system, New Supported Adaptation Functions:

• Resetting Adaptation, Calibration of Gear Position Sensor

Model XC90, Year 2016~2020, DDM / Driver Door Module, New Supported Adaptation Functions:

• Initializing the Window in the Front Door

Model XC90, Year 2016~2020, PDM / Passenger Door Module, New Supported Adaptation Functions:

• Initializing the Window in the Front Door

NEW SUPPORTED FUNCTIONS

Model V40 (Year 2018) – DIM (Instrument Cluster Module) System, Service Reset Function Supported

Model XC90 (2016-2020) & Model V40 (2017-2018) Short Test Function Increase Supported

Model XC90 (2016-2020)- ECM System

• Functions Supported include Reading / Clearing DTCs

• Improved Automatic Read Model Year Procedure

 

NEW IMPROVED DATA STREAM CAPABILITIES

Model S40 (Year 2006) – ECM system, New Improved Data Stream Capabilities

Model XC90 (2019-2020)- ECM system, New Improved Data Stream Capabilities

April 2020 Update Release

ALL NEW MODEL YEAR, ALL NEW SYSTEMS SUPPORTED

Model XC90, Increase Model Year Coverage to 2020, adding Read/Clear DTCs, Data Stream, Service Reset Functions for the following list of Systems:

◦ ECM

◦ TCM

◦ DEM (Differential Electronic Module)

◦ BCM (Brake Control Module)

◦ SAS (Steering Wheel Angle Sensor Module)

◦ PSCM (Power Steering Control module)

◦ VDDM (Vehicle Dynamic Domain Master)

◦ SRS

◦ DDM (Driver Door Module)

◦ PDM (Passenger Door Module)

◦ PSMD (Power Seat Module Driver)

◦ PSMP (Power Seat Module Passenger)

◦ POT (Power Operating Tailgate Module)

◦ BMS (Battery Monitoring Sensor)

◦ GSM (Gear Selector Module)

◦ OHC (Overhead Console)

◦ CCM (Climate Control Module)

◦ DIM (Instrument Cluster Module)

◦ CEM (Central Electronic Module)

◦ PAM (Parking Assist Module)

◦ AUD (Audio Module)

◦ IHU (Infotainment Head Unit)

◦ SODL (Side Obstacle Detection Control Module Left)

◦ SODR (Side Obstacle Detection Control Module Right)

◦ ASDM (Active Safety Domain Master)

◦ RML (Restraint Module Left)

◦ RMR (Restraint Module Right)

◦ SWM (Steering Wheel Module)

◦ PAC (Parking Assist Camera)

Model XC40, Increase Model Year Coverage to 2020, adding Read/Clear DTCs, Data Stream, Service Reset Functions for the following list of Systems:

◦ ECM

◦ TCM

◦ DEM (Differential Electronic Module)

◦ VDDM (Vehicle Dynamic Domain Master)

◦ SAS (Steering Wheel Angle Sensor Module)

◦ PSCM (Power Steering Control module)

◦ SRS

◦ DDM (Driver Door Module)

◦ PDM (Passenger Door Module)

◦ POT (Power Operating Tailgate Module)

◦ BMS (Battery Monitoring Sensor)

◦ EGSM (Electronic Gear Selector Module)

◦ TACM (Transmission Actuator Control Module)

◦ OHC (Overhead Console)

◦ CSD (Center Stack Display)

◦ CCM (Climate Control Module)

◦ DIM (Instrument Cluster Module)

◦ CEM (Central Electronic Module)

◦ AUD (Audio Module)

◦ IHU (Infotainment Head Unit)

◦ SODL (Side Obstacle Detection Control Module Left)

◦ SODR (Side Obstacle Detection Control Module Right)

◦ ASDM (Active Safety Domain Master)

◦ RML (Restraint Module Left)

◦ RMR (Restraint Module Right)

◦ VCM (Vehicle Connectivity Module)

◦ WAM (Wide Angle Vision Module)

◦ SWM (Steering Wheel Module)

Model S90 (Increase Model Year Coverage to 2017) / Model V90 (Increase Model Year Coverage to 2018) – adding Read/Clear DTCs and Service Reset Functions for the following list of Systems:

◦ ECM

◦ TCM

◦ BCM (Brake Control Module)

◦ SAS (Steering Wheel Angle Sensor Module)

◦ PSCM (Power Steering Control module)

◦ VDDM (Vehicle Dynamic Domain Master)

◦ SUM (Suspension Module)

◦ SRS

◦ DDM (Driver Door Module)

◦ PDM (Passenger Door Module)

◦ PSMD (Power Seat Module Driver)

◦ PSMP (Power Seat Module Passenger)

◦ POT (Power Operating Tailgate Module)

◦ CCM (Climate Control Module)

◦ DIM (Instrument Cluster Module)

◦ CEM (Central Electronic Module)

◦ PAM (Parking Assist Module)

◦ AUD (Audio Module)

◦ IHU (Infotainment Head Unit)

◦ SODL (Side Obstacle Detection Control Module Left)

◦ SODR (Side Obstacle Detection Control Module Right)

◦ ASDM (Active Safety Domain Master)

◦ RML (Restraint Module Left)

◦ RMR (Restraint Module Right)

◦ SCL (Steering Column Lock Module)

◦ VCM (Vehicle Connectivity Module)

◦ WAM (Wide Angle Vision Module)

Model S60, Increase Model Year Coverage to 2018, adding Data Stream Function for the following list of Systems:

◦ ECM

◦ TCM

◦ DEM (Differential Electronic Module)

◦ BCM (Brake Control Module)

◦ SAS (Steering Wheel Angle Sensor Module)

◦ PBM (Parking Brake Module)

◦ PSCM (Power Steering Control module)

◦ VDDM (Vehicle Dynamic Domain Master)

◦ SUM (Suspension Module)

◦ SRS

◦ FSM (Front Sensing Module)

◦ DDM (Driver Door Module)

◦ PDM (Passenger Door Module)

◦ PSM (Power Seat Module)

◦ CPM (Combustion Preheater Module)

◦ CVM (Closing velocity module)

◦ TRM (Trailer Module)

◦ CCM (Climate Control Module)

◦ DIM (Instrument Cluster Module)

◦ CEM (Central Electronic Module)

◦ PAM (Parking Assist Module)

◦ KVM (Keyless Vehicle Module)

◦ ICM (Infotainment Control Module)

◦ IAM (Integrated Audio Module)

◦ PHM (Phone Module)

◦ DABM (Digital Audio Broadcast Module)

◦ SODL (Side Obstacle Detection Control Module Left)

◦ SODR (Side Obstacle Detection Control Module Right)

NEW SUPPORTED ADAPTATION SPECIAL FUNCTIONS (DoIP Software & Hardware Integration with iSCAN)

Increase New Model Year Coverage for Model XC90 (- 2020), Model XC40 (- 2020), Model S90 (- 2017), Model V90 (- 2018) :

◦ Parking Brake Release to the Service Position

◦ Battery Reset to Zero Service

NEW SUPPORTED FUNCTIONS

Model V40 Cross, Short Test Function, Supported to Year 2016

Model S90, Short Test Function, Supported to Year 2017

 

January 2020 Update Release

NEW SUPPORTED COVERAGE

Model XC60, Model Year 2018-2019, adding Read/Clear DTCs & Service Reset Functions for the following list of Systems:

◦ ECM (B4204T23/B4204T27)

◦ TCM (TG-81SC AWD)

◦ DEM (Differential Electronic Module)

◦ BCM (Brake Control Module)

◦ SAS (Steering Wheel Angle Sensor Module)

◦ PSCM (Power Steering Control module)

◦ VDDM (Vehicle Dynamic Domain Master)

◦ SUM (Suspension Module)

◦ SRS

◦ DDM (Driver Door Module)

◦ PDM (Passenger Door Module)

◦ PSMD (Power Seat Module Driver)

◦ PSMP (Power Seat Module Passenger)

◦ POT (Power Operating Tailgate Module)

◦ HCML (Headlamp Control Module Left)

◦ HCMR (Headlamp Control Module Right)

◦ CCM (Climate Control Module)

◦ DIM (Instrument Cluster Module)

◦ CEM (Central Electronic Module)

◦ PAM (Parking Assist Module)

◦ AUD (Audio Module)

◦ IHU (Infotainment Head Unit)

◦ SODL (Side Obstacle Detection Control Module Left)

◦ SODR (Side Obstacle Detection Control Module Right)

◦ ASDM (Active Safety Domain Master)

◦ RML (Restraint Module Left)

◦ RMR (Restraint Module Right)

◦ SCL (Steering Column Lock Module)

◦ VCM (Vehicle Connectivity Module)

◦ VCM (Wide Angle Vision Module)

Model XC40, Model Year 2018, adding Read/Clear DTCs & Service Reset Functions for the following list of Systems:

◦ ECM (B4204T18)

◦ TCM (TG-81SC/TG-81SC AWD)

◦ SAS (Steering Wheel Angle Sensor Module)

◦ PSCM (Power Steering Control module)

◦ VDDM (Vehicle Dynamic Domain Master)

◦ SRS

◦ DDM (Driver Door Module)

◦ PDM (Passenger Door Module)

◦ POT (Power Operating Tailgate Module)

◦ EGSM (Electronic Gear Selector Module)

◦ TACM (Transmission Actuator Control Module)

◦ HCML (Headlamp Control Module Left)

◦ HCMR (Headlamp Control Module Right)

◦ CCM (Climate Control Module)

◦ DIM (Instrument Cluster Module)

◦ CEM (Central Electronic Module)

◦ PAM (Parking Assist Module)

◦ AUD (Audio Module)

◦ IHU (Infotainment Head Unit)

◦ SODL (Side Obstacle Detection Control Module Left)

◦ SODR (Side Obstacle Detection Control Module Right)

◦ ASDM (Active Safety Domain Master)

◦ RML (Restraint Module Left)

◦ RMR (Restraint Module Right)

◦ SCL (Steering Column Lock Module)

◦ VCM (Vehicle Connectivity Module)

◦ WCM (Wide Angle Vision Module)

Model V40 Cross, Model Year 2016, adding Read/Clear DTCs & Service Reset Functions for the following list of Systems:

 

◦ ECM (B4204T11/B4154T4/B4204T15/B4204T19/B204T21/B4204T37/D4204T9/D4204T14)

◦ TCM (TF-71SC/TG-81SC/TG-81SC AWD)

◦ DEM (Differential Electronic Module)

◦ BCM (Brake Control Module)

◦ PBM (Parking Brake Module)

◦ SAS (Steering Wheel Angle Sensor Module)

◦ PSCM (Power Steering Control module)

◦ SRS

◦ FSM ( Front Sensing Module)

◦ DDM (Driver Door Module)

◦ PDM (Passenger Door Module)

◦ PSM ( Power Seat Module)

◦ CPM (Combustion Preheater Module)

◦ CVM (Closing Velocity Module)

◦ TRM (Trailer Module)

◦ PPM (Pedestrian Protection Module)

◦ CCM (Climate Control Module)

◦ DIM (Instrument Cluster Module)

◦ CEM (Central Electronic Module)

◦ PAM (Parking Assist Module)

◦ KVM (Keyless Vehicle Module)

◦ ICM (Infotainment Control Module)

◦ IAM (Integrated Audio Module)

◦ PHM (Phone Module)

◦ DABM (Digital Audio Broadcast Module)

◦ SODL (Side Obstacle Detection Control Module Left)

◦ SODR (Side Obstacle Detection Control Module Right)

NEW SUPPORTED ADAPTATION SPECIAL FUNCTIONS (DoIP Software & Hardware Integration with iSCAN)

For CEM System, increase Battery Reset to Zero Service Function Adaptation for the following Models & Year Coverage:

◦ Model XC60 (Model Year 2019 – 2019)

◦ Model V50 (Model Year 2011- 2012)

◦ Model S80 (Model Year 2016)

◦ Model XC40 (Model Year 2018)

◦ Model V40 Cross (Model Year 2016)

For BCM (Brake Control Module) System, Increase Parking Brake Release to the Service Position Function Adaptation for the following Models & Year Coverage:

◦ Model XC60 (Model Year 2018 – 2019)

◦ Model S80 (Model Year 206)

◦ Model XC80 (Model Year 2016)

For VDDM (Vehicle Dynamics Domain Module) System, Increase Parking Brake Release to the Service Position Function Adaptation for the following Model & Year Coverage:

◦ Model XC40 (Model Year 2018)

Model XC60, Model Year 2016-2017, Whole System Search Function, Increase the Option of Short Test Report

Model XC60, Model Year 2018-2019, Increase Automatic Read Model Year Function

 

NEW IMPROVED DATA STREAM COVERAGE

Increase Data Stream Coverage for the following Models & Year & Systems:

◦ Model S60, Model Year 2015/2016 – ECM (B4204T9) System

◦ Model V40, Model Year 2016 – ECM(B4154T5/B4204T11/B4204T15/B4204T19/D4204T14) System

◦ Model V40, Model Year 2017– ECM(B4154T5/B4204T11/B4204T15/B4204T19/D4204T14) System

◦ Model V40, Model Year 2018– ECM(B4154T4/B4154T5/B4204T11/B4204T19/D4204T14) System

◦ Model S80, Model Year 2015 – ECM(B4204T11)/TCM(TG81SC)

/BCM/SAS/PBM/PSCM/SUM/SRS/FSM/DDM/PDM/PSM/CPM/CVM/TRM/CCM/DIM/CEM/PAM/KVM/PAC/ICM/IAM/PHM/DABM Systems

◦ Model S80, Model Year 2016 – ECM(B4204T11)/TCM(TG81SC)

/DEM/BCM/SAS/PBM/PSCM/SUM/SRS/FSM/DDM/PDM/PSM/CPM/CVM/TRM/CCM/DIM/CEM/PAM/KVM/PAC/ICM/IAM/PHM/DABM Systems

◦ Model V40, Model Year 2015 – ECM(B4164T/B4164T3/B4164T4/B4204T11/B5204T8/B5204T9/D4162T/D4204T14/D5204T6)/TCM(MPS6/TF80SD/TG81SC)

/BCM/SAS/PSCM/PBM/SRS/FSM/DDM/PDM/ PSM/ CPM/CVM/TRM/PPM/CCM/DIM/CEM/PAM/KVM/ICM/IAM/DABM/PHM/SODL/SODR Systems

◦ Model V40 Cross, Model Year 2015 – ECM(B4164T)/TCM(MPS6)

/BCM/SAS/PBM/PSCM/SRS/FSM/DDM/PDM/PSM/CPM/CVM/TRM/PPM/CCM/DIM/CEM/PAM/KVM/ICM/IAM/PHM/DABM/SODL/SODR Systems

.